Miele Gas Cooktop Igniter Problems
This repair guide provides step-by-step instructions on replacing the spark igniter switch in a gas cooktop. The spark igniter switch is located on the stem of the burner control valve. Replace the spark igniter switch with a manufacturer-approved replacement part if the burners don't spark when you turn the burner control knob to the Lite position or if igniters spark constantly even when the burners are off.
Dec 1, 2015 - Whether it's grease buildup or food crumbs, one of the most common causes for a gas burner that has trouble igniting is debris blocking gas.
Use these steps to replace a spark igniter switch in Kenmore, Frigidaire, Electrolux, Whirlpool, GE, KitchenAid, Maytag and Amana gas cooktops.
Repair difficulty:
Time required:
Less than 45 min.
Parts Required
Miele Gas Cooktop Igniter Problems Problems
- Spark igniter switch
For manuals, repair guides, and specific part recommendations, enter your model number.
Tools Required
- 1/4' nut driver
- Screwdriver
- Work gloves
Before you begin
Wear work gloves to protect your hands from sharp edges.
The cooktop and grates must be cool to the touch.
Warning: Undertaking repairs to appliances can be hazardous. Be sure to use the proper tools and safety equipment noted in the guide and follow all instructions. Do not proceed until you are confident that you understand all of the steps and are capable of completing the repair. Some repairs should only be performed by a qualified technician.
Unplug the power cord from the wall outlet and then close the gas supply shut-off valve.
Close the gas shut-off valve.
Step 2:Remove the burner heads
Remove all the cooktop grates and then lift the gas burner caps off the burner heads. Remove the screws that hold the burner heads in place and then remove the burner heads.
Pull the control knobs off of the burner control valves. Remove the screws that secure the main top to the top of the burner orifice holders. Lift the main top off of the cooktop and set it aside.
Remove the main top.
Tip: If the wire harness and switches are one component, as on this model, remove all the switches. On models with switches that can be removed individually, remove only the switch you're replacing.
Take a digital picture of the wires attached to the existing spark module or tag them with labeled masking tape so you can connect them correctly to the new spark module.
Disconnect all the wires attached to the spark module.
Remove the bushings from the stems of the burner control valves. Pull the spark igniter switches off of the burner control valves. Remove the switch and harness assembly from the cooktop and discard it.
Remove the spark module cover.
Free hd stream game of thrones. Disconnect the spark igniter switch harness wires.
Remove the silicone seals.
Lift the switches up off the gas valve stem.
Miele Gas Cooktop
Push the new switches onto the stems of the burner control valves.
Miele Gas Cooktop Problems
Reinstall the bushings on the burner control valve stems.
Using the digital picture or marked tape as a guide, connect the wires to the new spark module.
Push the new swtiches onto the stems of the burner valves.
Reinstall the silicone seals over the burner valve stems.
Connect the spark igniter harness wires to spark module.
Putty hyperterminal windows 10. Position the main top on top of the burner orifice holders. Insert and tighten the screws that secure the main top to the orifice holders. Push the control knobs on the burner control valves.
Reinstall top.
Reinstall and tighten the screws.
Position the burner heads in the correct locations, screw them into place and tighten the screws firmly. Cover the burner heads with the burner caps in the correct locations. Set the grates into place on the cooktop.
The password game. Reinstall the burner heads.
Install and tighten screws.
Install the burner caps.
Plug the power cord into the wall outlet and open the gas shut-off valve.